Tag: Cisco Certified Network Associate (200-301 CCNA)

Cisco Certified Network Associate (200-301 CCNA) – Question191

Which mode allows access points to be managed by Cisco Wireless LAN Controllers?

A. bridge
B. lightweight
C. mobility express
D. autonomous

Correct Answer: B

Explanation:

Explanation:
A Lightweight Access Point (LAP) is an AP that is designed to be connected to a wireless LAN (WLAN) controller (WLC). APs are “lightweight,” which means that they cannot act independently of a wireless LAN controller (WLC). The WLC manages the AP configurations and firmware. The APs are “zero touch” deployed, and individual configuration of APs is not necessary.

Cisco Certified Network Associate (200-301 CCNA) – Question190

Which mode must be used to configure EtherChannel between two switches without using a negotiation protocol?

A. active
B. on
C. auto
D. desirable

Correct Answer: B

Explanation:

Explanation:
The Static Persistence (or “on” mode) bundles the links unconditionally and no negotiation protocol is used. In this mode, neither PAgP nor LACP packets are sent or received.

Cisco Certified Network Associate (200-301 CCNA) – Question188

Which unified access point mode continues to serve wireless clients after losing connectivity to the Cisco Wireless LAN Controller?

A. local
B. mesh
C. flexconnect
D. sniffer

Correct Answer: C

Explanation:

Explanation:
In previous releases, whenever a FlexConnect access point disassociates from a controller, it moves to the standalone mode. The clients that are centrally switched are disassociated. However, the FlexConnect access point continues to serve locally switched clients. When the FlexConnect access point rejoins the controller (or a standby controller), all clients are disconnected and are authenticated again. This functionality has been enhanced and the connection between the clients and the FlexConnect access points are maintained intact and the clients experience seamless connectivity. When both the access point and the controller have the same configuration, the connection between the clients and APs is maintained.
Reference:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/confi…

Cisco Certified Network Associate (200-301 CCNA) – Question187

DRAG DROP
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
Select and Place:

Correct Answer: [img 0187-0001.jpg]

Explanation:

Explanation:
The service port can be used management purposes, primarily for out-of-band management. However, AP management traffic is not possible across the service port. In most cases, the service port is used as a “last resort” means of accessing the controller GUI for management purposes. For example, in the case where the system distribution ports on the controller are down or their communication to the wired network is otherwise degraded.
A dynamic interface with the Dynamic AP Management option enabled is used as the tunnel source for packets from the controller to the access point and as the destination for CAPWAP packets from the access point to the controller.
The virtual interface is used to support mobility management, Dynamic Host Configuration Protocol (DHCP) relay, and embedded Layer 3 security such as guest web authentication. It also maintains the DNS gateway host name used by Layer 3 security and mobility managers to verify the source of certificates when Layer 3 web authorization is enabled.
Reference:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-5/confi…

Cisco Certified Network Associate (200-301 CCNA) – Question186


Refer to the exhibit. After the switch configuration, the ping test fails between PC A and PC B. Based on the output for switch 1, which error must be corrected?

A. The PCs are in the incorrect VLAN.
B. All VLANs are not enabled on the trunk.
C. Access mode is configured on the switch ports.
D. There is a native VLAN mismatch.

Correct Answer: D

Cisco Certified Network Associate (200-301 CCNA) – Question185

Which configuration ensures that the switch is always the root for VLAN 750?

A. Switch(config)#spanning-tree vlan 750 priority 38418607
B. Switch(config)#spanning-tree vlan 750 priority 0
C. Switch(config)#spanning-tree vlan 750 root primary
D. Switch(config)#spanning-tree vlan 750 priority 614440

Correct Answer: C

Cisco Certified Network Associate (200-301 CCNA) – Question183

An engineer needs to configure LLDP to send the port description type length value (TLV). Which command sequence must be implemented?

A. switch(config-if)#lldp port-description
B. switch#lldp port-description
C. switch(config-line)#lldp port-description
D. switch(config)#lldp port-description

Correct Answer: D

Cisco Certified Network Associate (200-301 CCNA) – Question182

DRAG DROP

Refer to the exhibit. An engineer is required to verify that the network parameters are valid for the users' wireless LAN connectivity on a /24 subnet. Drag and drop the values from the left onto the network parameters on the right. Not all values are used.
Select and Place:

Correct Answer: [img 0182-0002.jpg]