What is the MAC address used with VRRP as a virtual address?

A. 00-05-42-38-53-31
B. 00-00-5E-00-01-0a
C. 00-00-0C-07-AD-89
D. 00-07-C0-70-AB-01

What are two benefits of FHRPs? (Choose two.)

A. They allow encrypted traffic
B. They prevent loops in the Layer 2 network.
C. They are able to bundle multiple ports to increase bandwidth
D. They enable automatic failover of the default gateway
E. They allow multiple devices to serve as a single virtual gateway for clients in the network

An engineer just installed network 10.120.10.0/24. Which configuration must be applied to the R14 router to add the new network to its OSPF routing table?

A. Router ospf 100
Network 10.120.10.0 0.0.0.255 area 0
B. Router ospf 120
Network 10.120.10.0 255.255.255.0 area 0
Ip route 10.120.10.0 255.255.255.0 fa0/1
C. Router ospf 100 area 0
Network 10.120.10.0 0.0.0.255
D. Router ospf 100
Network 10.120.10.0 255.255.255.0 area 0

Refer to the exhibit. How much OSPF be configured on the GigabitEthernet0/0 interface of the neighbor device to achieve the destined neighbor relationship?

A. Router(config)#interface GigabitEthernet 0/0
Router(config-if)#ip ospf cost 5
B. Router(config)#interface GigabitEthernet 0/0
Router(config-if)#ip ospf priority 1
C. Router(config)#interface GigabitEthernet 0/0
Router(config-if)#ip ospf area 2
D. Router(config)#interface GigabitEthernet 0/0
Router(config-if)#ip ospf network point-to-point

Refer to the exhibit. When router R1 receives a packet with destination IP address 10.56.0.62, through which interface does it route the packet?

A. Vlan58
B. Null0
C. Vlan59
D. Vlan60

Refer to the exhibit. After applying this configuration to router R1, a network engineer is verifying the implementation. If all links are operating normally, and the engineer sends a series of packets from PC1 to PC3, how are the packets routed?

A. They are distributed sent round robin to interfaces S0/0/0 and S0/0/1
B. They are routed to 10.0.0.2
C. They are routed to 192.168.100.2
D. They are routed to 172.16.20.2

Refer to the exhibit. What is the prefix length for the route that router1 will use to reach host A?

A. /25
B. /27
C. /28
D. /29

Refer to the exhibit. An OSPF neighbor relationship must be configured using these guidelines:
* R1 is only permitted to establish a neighbor with R2.
* R1 will never participate in DR elections.
* R1 will use a router-id of 10.1.1.1.
Which configuration must be used?

A.

B.

C.

D.

Refer to the exhibit. An engineer is checking the routing table in the main router to identify the path to a server on the network. Which route does the router use to reach the server at 192.168.2.2?

A. S 192.168.0.0/20 [1/0] via 10.1.1.1
B. S 192.168.2.0/29 [1/0] via 10.1.1.1
C. S 192.168.2.0/28 [1/0] via 10.1.1.1
D. S 192.168.1.0/30 [1/0] via 10.1.1.1

Refer to the exhibit. The image server and client A are running an application that transfers an extremely high volume of data between the two. An engineer is configuring a dedicated circuit between R1 and R2. Which set of commands must the engineer apply to the routers so that only traffic between the image server and client A is forces to use the new circuit?

A. R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.6
R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.5
B. R1(config)#ip route 10.10.13.10 255.255.255.128 10.10.10.6
R2(config)#lp route 192.168.0.100 255.255.255.0 10.10.10.5
C. R1(config)#ip route 10.10.13.10 255.255.255.252 10.10.10.6
R2(config)#tp route 192.168.0.100 255.255.255.252 10.10.10.5
D. R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.2
R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.1